Search Results

An investigation of several diesel injector nozzles that produced different engine emissions performance was performed. The nozzle styles used were two VCO type nozzles that were manufactured using two different techniques, and two mini-sac nozzles that provided comparison. Fired experiments were conducted on a Detroit Diesel Series 50 engine. Optical access was obtained by substituting a sapphire window for one exhaust valve. Under high speed, high load, retarded injection timing conditions, it was discovered that each nozzle produced different specific soot and NOx emissions. High-speed film images were obtained. It was discovered that the temperature and KL factor results from the 2-color optical pyrometry showed significant differences between the nozzles. The authors propose the possibility that differences in air entrainment, caused by potential differences in CD due to surface finish, may contribute to the variance in emissions performance.

Combustion under stratified operating conditions in a direct-injection spark-ignition engine was investigated using simultaneous planar laser-induced fluorescence imaging of the fuel distribution (via 3-pentanone doped into the fuel) and the combustion products (via OH, which occurs naturally). The simultaneous images allow direct determination of the flame front location under highly stratified conditions where the flame, or product, location is not uniquely identified by the absence of fuel. The 3-pentanone images were quantified, and an edge detection algorithm was developed and applied to the OH data to identify the flame front position. The result was the compilation of local flame-front equivalence ratio probability density functions (PDFs) for engine operating conditions at 600 and 1200 rpm and engine loads varying from equivalence ratios of 0.89 to 0.32 with an unthrottled intake. Homogeneous conditions were used to verify the integrity of the method.

Diesel exhaust particulate trap system is one of the most effective means to control diesel particulate emissions from diesel vehicles. In this paper, a recently developed diesel exhaust particulate trap system was described and experimentally studied. This system employed a wall-flow ceramic foam filter, which was made of silicon carbide or chromium oxide. And this system was equipped with a microwave heater for the purpose of filter regeneration. Engine dynamometer testing, vehicle bench testing and on-road evaluation of this system were conducted. The experiments studied on the filtration efficiency of this system, the effectiveness of filter regeneration, the power penalty of the vehicle, the ability of noise suppression of this system, and the durability of this particulate trap system. The experimental results showed that this diesel particulate trap system was effective, reliable, and durable.

This paper describes the development of the drive motor used on a newly developed electric vehicle (EV) that has been specifically designed and engineered as the world's first mass-produced EV. Producing maximum torque of 280 Nm and maximum power of 80 kW, this synchronous motor was selected as the first electrified powertrain to be named to Ward's 10 Best Engines list for 2011. In developing this motor, magnetic field simulations were conducted in the process of adopting the following in-house technologies to achieve a compact motor size, high output and high efficiency. The rotor shape has the interior permanent magnets arranged in a ▽-shaped that achieves a superior balance of torque and power. The flux barriers located on the outer periphery are designed to reduce iron loss. The V-shaped flux barriers provide both excellent mechanical strength and outstanding performance during high-speed motor operation.

The first-ever application of a hydrogen-free diamond-like carbon (H free DLC) coating to a mass-production gasoline engine reduces friction between the cylinder bore and piston by 18%. It is explained the reducing friction effect of H free DLC by oil film thickness of piston ring. When H-free DLC is applied to top ring, friction is over 10% reduced. Because low friction coating is effective in a thin oil film at a large area near top dead center (TDC). It is also found that the friction reduction effect is enhanced when low viscosity engine oil is used. DLC as a low friction coating is more effective in a thinner oil film. In this study, the adhesion strength of H-free DLC coating on piston rings is improved because of providing a smooth substrate, the new washing process and the optimized coating characteristics. Adhesion strength is verified by test results using actual parts considered to contribute to piston ring load.

Customers desire to keep the interior of their vehicles as clean as possible. A field survey was made of the types of dirt and stains found on interior trim parts as the starting point for the development of products that meet this need. The survey findings showed that soiled stains resulting from long periods of use are commonly found on seat surfaces and cloth seats also have beverage stains. Dirt stains are typically seen on plastic trim parts. An analysis of the components of soiled stains revealed the presence of higher fatty acids that tend to adhere to the urethane coating on the surface of genuine leather seat covers and to the polyester fibers of cloth seat covers. A coating technology was then developed for bringing dirt to the surface so that it can be easily removed by wiping with a wet cloth.

This paper describes a functionality and test results of moving object detection based on vision system. Moving object detection is realized by just adding image processing software to the vision system with no additional sensor. Moreover, by usage of around view monitor system as vision system, existence of moving objects surrounding the subject vehicle can be informed to support the driver in the parking maneuver.

This paper describes a new 1.2-liter three cylinder gasoline engine named HR12DDR, with the target to achieve the lowest level CO2 in the European B-segment market and also, to satisfy the customer's driving pleasure through high output performance. This engine is developed with the consideration of meeting further strict regulations in the years ahead and of the possibility of being an alternative powertrain of diesel in the future as well. As a first step this engine was applied on the European Nissan Micra in 2011; achieving 95g/km CO2 emissions(NEDC mode). This low fuel consumption was realized mainly through technologies which scope to maximize thermal efficiency with high compression ratio, and to minimize the mechanical friction loss. The combustion was optimized by Direct injection (DI)system. To obtain the better fuel economy performance without sacrificing high output, we chose the supercharger system with bypass valve and electromagnetic clutch.

A, three-dimensional CFD code, based on the KIVA code, is used to explore alternatives to conventional DI diesel engine designs for reducing NOx and soot emissions without sacrificing engine performance. The effects of combustion chamber design and fuel spray orientation are investigated using a new proposed GAMMA engine concept, and two new multiple injector combustion system (MICS) designs which utilize multiple injectors to increase gas motion and enhance fuel/air mixing in the combustion chamber. From these computational studies, it is found that both soot and nitrous oxide emissions can be significantly reduced without the need for more conventional emission control strategies such as EGR or ultra high injection pressure. The results suggest that CFD models can be a useful tool not only for understanding combustion and emissions production, but also for investigating new design concepts.

Evaluation of pedestrian leg protection performance using the Flex-PLI-GTR (Flexible Pedestrian Legform Impactor Global Technical Regulation) impactor is initiated in JNCAP in 2011. Therefore, a finite element (FE) model of Flex-PLI-GTR is needed for use in digital car development in order to satisfy pedestrian leg protection performance requirements. This paper describes the FE model of Flex-PLI-GTR that has been developed to meet this need. There are three important features of this FE model for obtaining sufficient simulation accuracy. First, the shapes of all Flex-PLI-GTR structures were modeled in detail. Shape information of the inner structures was obtained by computerized tomography scanning and shape information of the inner structures of the outer skin was obtained by laser measurement. Furthermore, the shape of the wrapped skin was incorporated into the FE model based on a wrapping simulation.

This paper describes a newly developed hydraulic variable valve timing control (VTC) system, targeting the internal combustion gasoline engine, with an optimum angular position locking mechanism to reduce tailpipe emissions (TPE). In general, emission control catalysts are used as one measure to reduce TPE. However, there is the issue that catalysts cannot remove pollutants before reaching its light-off temperature at cold engine start. To address this issue, we have been using a method of increasing the valve overlap period between intake valve opening (IVO) and exhaust valve closing (EVC) by operating a VTC system at engine start. This brings engine-out emissions (EOE) back to the combustion chamber to be burned, thereby reducing EOE levels. However, this method requires about 3 seconds for the sufficient hydraulic pressure to start VTC operations.

The present work is aimed at developing a computational model of the interelectrode phenomena in thermionic energy converters which will be accurate over a very wide range of plasma conditions and operating modes. Previous models have achieved only moderate degrees of accuracy and, in a limited range, of validity. This limited range excludes a number of advanced thermionic devices, such as barium-cesium converters. The model under development promises improved accuracy in prediction of conventional devices and extension of predictive capability to advanced devices. The approach is to adapt the “Converted Scheme”, or CS method, to the cesium vapor plasma diode. This method, developed at the University of Wisconsin- Madison, is an extremely efficient algorithm for the solution of charged-particle kinetic equations and has been successfully used to simulate helium RF glow discharges.

A new transparent resin material developed by uniformly dispersing a nano-filler (boehmite particles, 5 nm in diameter and 197 nm long) in polycarbonate resin combines a flexural modulus of 5.9 GPa, a linear expansion coefficient of 35 ppm/K, and excellent mechanical toughness with excellent optical characteristics (transparency with 1.1% haze at 1 mm thick). These characteristics make this material highly suitable as a replacement for automotive glass that allows innovative design, a liberating sense of openness for automobiles.

Progress on the development and validation of a CFD model for diesel engine combustion and flow is described. A modified version of the KIVA code is used for the computations, with improved submodels for liquid breakup, drop distortion and drag, spray/wall impingement with rebounding, sliding and breaking-up drops, wall heat transfer with unsteadiness and compressibility, multistep kinetics ignition and laminar-turbulent characteristic time combustion models, Zeldovich NOx formation, and soot formation with Nagle Strickland-Constable oxidation. The code also considers piston-cylinder-liner crevice flows and allows computations of the intake flow process in the realistic engine geometry with two moving intake valves. Significant progress has been made using a modified RNG k-ε turbulence model, and a multicomponent fuel vaporization model and a flamelet combustion model have been implemented.

A direct calibration has been performed on laser-induced fluorescence measurements of the oil film in a single cylinder air-cooled research engine by simultaneously measuring the minimum oil film thickness by the capacitance technique. At the minimum oil film thickness the capacitance technique provides an accurate measure of the ring-wall distance, and this value is used as a reference for the photomultiplier voltage, giving a calibration coefficient. This calibration coefficient directly accounts for the effect of temperature on the fluorescent properties of the constituents of the oil which are photoactive. The inability to accurately know the temperature of the oil has limited the utility of off-engine calibration techniques. Data are presented for the engine under motoring conditions at speeds from 800 - 2400 rpm and under varying throttle positions.

Although turbocharging can extend the high load limit of low temperature combustion (LTC) strategies such as reactivity controlled compression ignition (RCCI), the low exhaust enthalpy prevalent in these strategies necessitates the use of high exhaust pressures for improving turbocharger efficiency, causing high pumping losses and poor fuel economy. To mitigate these pumping losses, the divided exhaust period (DEP) concept is proposed. In this concept, the exhaust gas is directed to two separate manifolds: the blowdown manifold which is connected to the turbocharger and the scavenging manifold that bypasses the turbocharger. By separately actuating the exhaust valves using variable valve actuation, the exhaust flow is split between two manifolds, thereby reducing the overall engine backpressure and lowering pumping losses. In this paper, results from zero-dimensional and one-dimensional simulations of a multicylinder RCCI light-duty engine equipped with DEP are presented.

A transmission system model for Ford Motor Company's automatic transmission (AOD) system used in the Lincoln Town Car has been developed using the free-body diagram method (Newtonian approach). This model is sophisticated enough to represent the dynamic behavior of the transmission system, yet simple enough to use as a real time computer simulation tool, and as an embedded model within a dynamic observer. The transmission system and torque converter models presented in this paper are part of a larger powertrain system model at the Powertrain Control Research Laboratory, University of Wisconsin-Madison.

An experimental study was performed to investigate the effect of fuel composition on combustion, gaseous emissions, and detailed chemical composition and size distributions of diesel particulate matter (PM) in a modern heavy-duty diesel engine with the use of the enhanced full-dilution tunnel system of the Engine Research Center (ERC) of the UW-Madison. Detailed description of this system can be found in our previous reports [1,2]. The experiments were carried out on a single-cylinder 2.3-liter D.I. diesel engine equipped with an electronically controlled unit injection system. The operating conditions of the engine followed the California Air Resources Board (CARB) 8-mode test cycle. The fuels used in the current study include baseline No. 2 diesel (Fuel A: sulfur content = 352 ppm), ultra low sulfur diesel (Fuel B: sulfur content = 14 ppm), and Fisher-Tropsch (F-T) diesel (sulfur content = 0 ppm).

The effect of ambient gas density and the number of injector holes on the characteristics of airflow surrounding non-evaporating transient diesel sprays inside a constant volume chamber were investigated using a 6-hole injector. Particle Image Velocimetry (PIV) was used to measure the gas velocities surrounding a spray plume as a function of space and time. A conical control surface surrounding the spray plume was chosen as a representative side entrainment surface. The positive normal velocities across the control surface of single-hole injection sprays were higher than those of 6-hole injection sprays. An abrupt increase in velocities tangential to the control surface near the chamber wall suggests that the recirculation of surrounding gas is accelerated by spray wall impingement.

An experimental study was carried out to investigate the effects of fuel injection timing on detailed chemical composition and size distributions of diesel particulate matter (PM) and regulated gaseous emissions in a modern heavy-duty D.I. diesel engine. These measurements were made for two different diesel fuels: No. 2 diesel (Fuel A) and ultra low sulfur diesel (Fuel B). A single-cylinder 2.3-liter D.I. diesel engine equipped with an electronically controlled unit injection system was used in the experiments. PM measurements were made with an enhanced full-dilution tunnel system at the Engine Research Center (ERC) of the University of Wisconsin-Madison (UW-Madison) [1, 2]. The engine was run under 2 selected modes (25% and 75% loads at 1200 rpm) of the California Air Resources Board (CARB) 8-mode test cycle.